ITC-2530 Assignment Details and Directions

This page is organized into sections based on the category of your final grade that the assignment will fall into. Be sure to check the syllabus for information about how the categories are weighted in your final grade.

Lab & Homework Assignments

Packet Tracer Online Submissions

Each of these activities will be submitted using the Packet Tracer ScoreUP Online Submission process. Points will be earned for each submitted activity based on correctness and completion of the activity. You will see a completion percentage for each activity in the Packet Tracer software before submitting. Remember to submit through ScoreUP inside of Packet Tracer and to save for yourself a copy of your finished activity file in case it’s requested by your instructor.

  1. PT 2.2.13 - Point-to-Point Single-Area OSPFv2 Configuration (7 points)

  2. PT 2.3.11 - Determine the DR and BDR (7 points)

  3. PT 2.4.11 - Modify Single-Area OSPFv2 (7 points)

  4. PT 2.5.3 - Propagate a Default Route in OSPFv2 (7 points)

  5. PT 2.6.6 - Verify Single-Area OSPFv2 (7 points)

  6. PT 2.7.1 - Single-Area OSPFv2 Configuration (7 points)

  7. PT 5.1.8 - Configure Numbered Standard IPv4 ACLs (7 points)

  8. PT 5.1.9 - Configure Named Standard IPv4 ACLs (7 points)

  9. PT 5.2.7 - Configure and Modify Standard IPv4 ACLs (7 points)

  10. PT 5.4.12 - Configure Extended IPv4 ACLs - Scenario 1 (7 points)

  11. PT 5.4.13 - Configure Extended IPv4 ACLs - Scenario 2 (7 points)

  12. PT 5.5.1 - IPv4 ACL Implementation Challenge (7 points)

  13. PT 6.4.5 - Configure Static NAT (7 points)

  14. PT 6.5.6 - Configure Dynamic NAT (7 points)

  15. PT 6.6.7 - Configure PAT (7 points)

  16. PT 6.8.1 - Configure NAT for IPv4 (7 points)

  17. PT 10.3.4 - Configure and Verify NTP (7 points)

  18. PT 10.6.10 - Back Up Configuration Files (7 points)

  19. PT 10.7.6 - Use a TFTP Server to Upgrade a Cisco IOS Image (7 points)

  20. PT 10.8.1 - Configure CDP, LLDP, and NTP (7 points)

  21. PT 12.5.13 - Troubleshoot Enterprise Networks (7 points)

  22. PT 12.6.2 - Troubleshooting Challenge - Use Documentation to Solve Issues (7 points)

  23. PT 2.4.11 - Modify Single-Area OSPFv2 (7 points)

Lab Reports

For each module having lab activities you will need to submit one lab report which covers all of the lab activities listed below in the module. Submissions are made through the IHCC D2L site. You do not need to submit answers to the questions in the activities, those are for your own learning use only. Lab activities may include remote equipment access, campus equipment, or packet tracer activities. Good lab reports in this class are typically 325-650 words long. If you work with a partner on a lab you only need to submit a single lab report for the two of you but it must have both your names on it. Each lab report is worth up to 20 points.

If you have not done lab reports in one of Dr. Franske’s classes before, or you want to try and score better on lab reports, be sure to check out the instructions for writing lab reports page and example reports!
When Using Netlab Remote Lab System

  • The login password for CAASP Pod PCs in Netlab is: password

  • The login password for Internet Pod PCs in Netlab is: password

  1. Lab 2.7.2 - Single-Area OSPFv2 Configuration

  2. Lab 3.8.8 - Explore DNS Traffic

    This lab activity requires using Wireshark on an Internet connected PC. We don’t have it setup in Netlab yet so you can do it on your home computer or a lab computer on campus.

  3. PT 4.1.4 - ACL Demonstration

  4. Lab 5.5.2 - Configure and Verify Extended IPv4 ACLs

    When enabling HTTPS on newer Cisco devices you must map the HTTPS server to a trustpoint (certificate) on the router. See this StackExchange question for details on how to do this.

  5. PT 6.2.7 - Investigate NAT Operations

  6. Lab 6.8.2 - Configure NAT for IPv4

  7. PT 7.6.1 - WAN Concepts

  8. PT 10.1.5 - Use CDP to Map a Network

  9. PT 10.2.6 - Use LLDP to Map a Network

  10. Lab 10.6.11 - Use Tera Term to Manage Router Configuration Files

  11. Lab 10.6.12 - Use TFTP, Flash, and USB to Manage Configuration Files

    If you are working on a device with multiple IP interfaces it is sometimes required to set a default source interface which will be used by TFTP for communicating with the TFTP server. Some Cisco devices do not seem to automatically pick a correct source interface. When this happens you can end up with a situation where you can ping from the device to the TFTP server’s IP address but you are unable to send or receive files over TFTP. For example, in this lab on the router we’re only setting an IP on G0/0/1 so that would be the one we should set as the source interface like "ip tftp source-interface gi0/0/1"

  12. Lab 10.6.13 - Research Password Recovery Procedures .* After researching the recovery procedures set a hostname and enable password on a router and save the configuration. Try to reset the password on the router while keeping the hostname set the same following the procedures you have researched.

    If you are working on remote lab equipment you can do password recovery too, the process is a little different but our system does allow you to power on and off network devices as well as to send the BREAK command to devices which are the basics for router password recovery. Recovering passwords on switches can require physical access to hold down a button on the switch while powering up unless some additional configuration is done so you should not try setting an unknown password on a remotely accessed lab switch. See this video showing the password recovery process on Netlab.

  13. Lab 10.8.2 - Configure CDP, LLDP, and NTP

    Some Cisco devices do not have "hardware clocks" (also known as "calendars) anymore so if you are unable to get the "ntp update-calendar" command to work in Part 4, Step 4b it may not exist on your device.

  14. PT 11.5.1 - Compare Layer 2 and Layer 3 Devices

  15. PT 12.6.1 - Troubleshooting Challenge - Document the Network

  16. Lab 13.6.1 - Install Linux in a Virtual Machine and Explore the GUI

    It is suggested you complete this lab on your home computer if it has enough RAM to run the VM. However, if you need a Netlab system to install on please contact your instructor.

Homework

Homework activities will require submitting the actual answers to each question in the activity and may require showing your work as well. Homework assignment are individual, you and your lab partner need to both turn them in separately even if you work on them together.

  • Participate in an online forum discussion (typically 3 quality posts or more) of each module on the IHCC D2L site. See the forum posting page for details. (up to 10 points each module based on quality)

Discussion forum posts are usually worth a larger portion of your final grade than most students expect! If you have not done discussion posts in one of Dr. Franske’s classes before, or you want to try and score better on discussion forum postings, be sure to check out the instructions for participating in forum discussions and example posts!

Participation Activities

Any participation activities completed in the course will go here. This falls into the participation category of your course grade. Note that participation activities are not always that you get all the points just for dong them. These are just activities which measure your participation and engagement in the class. How each activity is graded is noted after the activity in the list below.

  • Complete a Course Introduction exam (20 points based on your score)

  • Complete the online practice final exam (10 points for attempting)

  • Complete the online Packet Tracer Practice Skills Assessment (10 points for attempting)

  • Complete the CCNA Certification Practice Exam (10 points for attempting)

  • Complete a weekly online check-in form or meet with the instructor during class to discuss course progress and ask questions (up to 10 points each based on progress)

Unit Assessments

You are responsible for completing all of the online unit assessments listed below. Multiple modules are included in single exams. These exams fall into the online assessments category of your course grade. If you are not able to complete an exam by the due date listed on the course schedule it is your reponsibility to contact the instructor prior to the due date for the exam. Contacting the instructor after the due date for the exam will usually mean the late work policy will apply (see the syllabus). For example, if the exam reports as not activated, or the website is down, you have lost Internet access, etc. contact the instructor as soon as possible for assistance. These exams are on the Cisco NetAcad site.

  • Module 1-2 OSPF Concepts and Configuration Exam

  • Module 3-5 Network Security Exam

  • Module 6-8 WAN Concepts Exam

  • Module 9-12 Optimize, Monitor, and Troubleshoot Networks Exam

  • Module 13-14 Emerging Network Technologies Exam

Skills Final Exams

The Skills Final Exams are designed to test your ability to apply the concepts learned in this class and practiced in labs to common, real-world scenarios. There are two parts to this portion of your grade from CCNA 3.

  • Completing all parts of the online Packet Tracer Skills Assessment (PTSA) at home. You grade will be based on correctly completing all parts of the activity. You will be able to use outside resources for this part of the exam.

  • Completing a lab equipment skills exam. You will not be able to use any resources other than those specified by your instructor on this part of the exam.

Regular Final Exams

You will need to complete an online final exam on the Cisco NetAcad site.

Document Build Time: 2026-01-30 22:23:19 UTC
Page Version: 2026.01
Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License